Question about Honda Motorcycles

2 Answers

What is the procedure to adjust the drive clutch on a honda 3813? Looks like there are several adjusting points @

Posted by john miller on

×

2 Answers

Gregg Mahin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Vr2020 Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Honda Master
  • 63,525 Answers

Hi, John you need to repost your question under the Tractor category, not Motorcycles. Thanks, Gregg

Posted on May 07, 2020

Attique-ur-Rehman

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Vr2020 Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 2,677 Answers

Http://blog.hondalawnparts.com/how-to-change-a-honda-ht3813-pto-clutch/

Posted on Mar 28, 2020

  • Ruby
    Ruby Mar 28, 2020

    My ex-wife makes $250 /hour on the laptop.She has been fired for seven months but last month her pay check was $17147 just working on the laptop for a few hours.
    Read more here>>>HERE www.earnmoney99.cOm

  • Attique-ur-Rehman
    Attique-ur-Rehman Mar 29, 2020

    https://www.youtube.com/watch?v=aA-r48yZ...

×

5 Related Answers

scott carlson

  • 60 Answers

SOURCE: Clutch Adjustment

You could try bleeding the slave cylinder. But it is very difficult and may or may not work. You may want to take it to an independent shop or back to the dealer. A special tool is needed inorder to depress the slave cylinder to properly bleed the possible air out of the system. It's a less expensive thing to try before replacing the clutch assy.

Posted on Feb 27, 2009

Anonymous

  • 9 Answers

SOURCE: 1997 Honda Civic EX Clutch

replace it

Posted on Apr 21, 2009

Anonymous

  • 28 Answers

SOURCE: 1997 Honda Magna VF45c 750 clutch adjustment

Did you do an oil change recently? Sometimes a motor cycles clutch shares the oil with the engine and a different kind of oil then the bike requires will cause the clutch to slip. This happens alot especially if someone switches to some types of synthetic oil when the bike had regular oil before the oil change.

Posted on Jun 24, 2009

tombones

  • 3567 Answers

SOURCE: on 2005 honda cmx 250 rebel does cam chain

Your bike has an automatic adjusting cam chain tensioner. No adjustment needed.

Can I get a “very helpful” rating on this answer? < And it doesn’t cost anything extra!

Posted on Jul 06, 2009

Roger Geer

  • 78 Answers

SOURCE: honda lawn mower wheel drive works, but needs adjustment, how?

Take the covers off the drive,there should be a hollow bolt the cable comes thru, it should have 2 adjustment nuts This lengthens or shorts the cable. There also may be a adjustment on the handle.

Posted on Oct 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 VFR750 rc36-fl clutch adjustment


Hi, Glynn for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Clutch adjustment
1990 1997 Honda VFR750 Clutch Replacement in 15 Minutes
Honda VFR750F Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda 1991 VFR750F Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


May 29, 2017 | Honda Motorcycles

15 Answers

On my 1987 honda shadow 1100 clutch handle comes almost all the way out before catching can i adjust it or do i need to replace clutch disc or any thing else


while engine is not running follow the clutch cable back to its point of origin & look for any other clutch adjustments besides the the one at the clutch handle if all clutch cable adjustments are backed off & clutch is still slipping its time for a new clutch assy buy a clymers repair manual,

Oct 10, 2014 | 1987 Honda VT 1100 C Shadow

1 Answer

Biting point on clutch lever is right at the end


find your master cyl. there should be adjust rod there

Mar 31, 2014 | Honda VTR 1000 F Firestorm Motorcycles

1 Answer

Adjust clutch on VTRs 1000


If it has a cable there is an adjustment at the lower end where it attaches to the engine.

Mar 31, 2014 | 1998 Honda VTR 1000 F Firestorm

1 Answer

How to adjust the clutch on ariens hydro 42


If you need the clutch adjusted there is a specific sequence for adjusting the clutch.I would spray with WD-40 or penetrating oil on the clutch movement , on the shaft (just in front of the engine) under the belts, there is only about 1/4" or so movement. Also lube all the linkage pivot points. If you still need to adjust the clutch download the manual with the model and serial number from Ariens.com and follow the procedures in the manual.

Apr 02, 2012 | Garden

1 Answer

2009 Honda Shadow Aero clutch adjustment


Hi, Walter for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch cable adjustment
Basics to Motorcycle Clutch Adjustment
Honda VT750C2 Shadow Spirit Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VT750C 2005 Shadow Aero Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Jan 08, 2012 | 2009 Honda Shadow Aero

1 Answer

I have a 2004 Honda VT750 Shadow Aero (shaft drive). Clutch apparently needs adjustment. Nuetral is easy to find but when shifting into 1st or 2nd or any other gear, bike stops. Is this a simple cable...


Adjustment is made at clutch end first and then fine-tuned at the handle bar end. Adjust at clutch end until there is no free play on the lever. Then slack off the nut a quarter turn. Test clutch operation and adjust at the lever end if nescessary. Remember to lock the nuts at the clutch end.

Feb 13, 2011 | Honda VT 750 Shadow Aero Motorcycles

1 Answer

How do you adjust clutch on 1994 Honda 1000F CBR


Hi there,

CBRs have hydraulic clutches and therefore are adjustment free/cannot be adjusted.

If you are getting some slip, change the clutch fluid for synthetic oil. If this still does not help, it might be time for new clutch plates. Maybe go for kevlar or carbon if you're flush to help reduce the chances of slippage.

If you just want to adjust the clutch lever, you can by unscrewing the little lever on the clutch lever and bringing the lever closer to the handlebars. This will have the effect of changing the biting point (but really it is the lever that has moved).

I hope this helps you and please vote for me if so. Thanks.

Jun 28, 2010 | 2008 Honda CB 1000R

1 Answer

I am looking for sevice bulletins for honda 3813 lawn tractor


I had a similar problem with my Honda 3813. When I tore it down, I found that the 3813 has a slow delay cyclinder - something like a shock absorber - the slowly puts pressure on the clutch plate after you let up on the clutch pedal. In my case, the clutch is old and worn, this is exactly the symptom I experienced because the clutch was nearly worn out - it took like 10 or more seconds to get going. A new drive clutch and a little adjustment fixed this problem for me. To replace the clutch without removing the engine I had to cut the cross brace plate on the bottom of the tractor.

To get to this you need to remove all the tin that is under the seat part of the tractor - a real nuisance.

Also, it took me 3 months to get the clutch from the Honda dealer. .... definitely not helpful! Good thing I had a John Deere as a backup, I've never had trouble getting parts quickly for that.

Mar 13, 2009 | Garden

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6392 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...