Question about Zebra Office Equipment & Supplies

2 Answers

I want to know how to stop auto calibration when my zebra printer got ON

Posted by Muhammad Sadiq on

2 Answers

Attique-ur-Rehman

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Vr2020 Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Zebra Master
  • 2,670 Answers

Posted on Apr 03, 2020

steve

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Vr2020 Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Zebra Master
  • 35,301 Answers

Go to zebras website and download the manual for free. its in the settings for all zebra printers i know of

Posted on Apr 03, 2020

5 Related Answers

Anonymous

  • 13 Answers

SOURCE: Zebra S600 printer continues calibrating

The factory default settings for the S600 is to auto calibrate every time the printhead is closed and every time the power is cycled. If the media sensor is not positioned correctly for the media you are using the label size will not be detected during a calibration. You mentioned the media has no markings, doe sthe media have a space between the labels? If so, the media sensor may not see the gap in the labels adn therefor is not calibrating properly or not calibrating at all. Check the media sensor position. I have found that the media sensor must be at least 1" from the inner wall of the printer so it doesn't see the edge of the backing in oder to read the size of the labels.

Posted on Feb 02, 2008

Anonymous

  • 5 Answers

SOURCE: Printer = Zebra TLP 2844-Z Problem = will not calibrate

just switch off the printer ,and then hold the green button power on the printer now and wait upto 4 bliknks of green led then remove the fingers.now printer will calibrate the label..

if still the problem exist .check the notch in the ribbon core.an adjust the spring tenson of rippon supply and take of roolers in printer

Posted on Dec 05, 2008

Anonymous

  • 3 Answers

SOURCE: My Zebra z4m plus

in the setup menu there is an option to choose what the machine does on powerup and head close. Yours is probably set to calibrate. Just change that setting to "none". Same thing with the pausing. there is a setting to pause after printing each label. Just change that option.

Posted on Jan 27, 2009

Anonymous

  • 31 Answers

SOURCE: I have a zebra TLP 3844-Z printer. My printer

Sounds like it is set to do a label length check at power on. Go into your printer preferences and set it to "do nothing" on power up.

e07a00e.jpg

Posted on Jun 27, 2009

Bob Miller

  • 97 Answers

SOURCE: my Zebra TLP 2844 printer

After calibration and printing the config, the printer will stay in Dump until you press the feed key again.

Hope that helps !

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I shut off the auto calibration on start-up? Every morning 1 am wasting 4 labels and ribbon for calibration.


Can only be done by sending a ZPL command. The ZPL manual can be downloaded from the Zebra web site.

Apr 28, 2011 | Zebra Stripe S600 Thermal Label Printer

1 Answer

My Zebra TLP 2844 printer gives me a no gap detected msg. and when I run the auto calibration sequence It prints the information but doesnt go out of Dump.


After calibration and printing the config, the printer will stay in Dump until you press the feed key again.

Hope that helps !

Sep 02, 2010 | Zebra Printer 140-751-00000

1 Answer

My zebra printer gives me a message no paper, it does have paper what can i do


If your printer is set for Auto Calibration on power up or when the printhead is closed and the label doesn't calibrate, then check the position of the sensor which is the red light. You didn't say how wide the label is but it may that the sensor is not positioned under the label. If it's out of position, the label won't calibrate.

Hope that helps !

Jun 09, 2010 | Zebra S4M Thermal Label Printer

2 Answers

Why is my Zebra printer printing every other label?


The labels you are printing have an extra line feed (a blank line) after the last printed line. Remove them.

Remove any "FormFeed" from the label run, if you are doing a "merge".


Line 1 Name
Line 2 Address
Line 3 Address2
Line 4 City St Zip
Line 5 <Blank>
Line 6 <Blank>

Sep 21, 2009 | Zebra LP 2844 Thermal Printer

1 Answer

Zebra Z4Mplus won't calibrate 2" Circle Labels


try to set the printer to the factory default setting

Aug 13, 2009 | Zebra Z4M Printer

1 Answer

Zebra stripe s500 skips 5 labels prints 1 skips 1


He are the steps you need to calibrate your printer

Label Length Calibration
Note: This is typically the only procedure required when first installing the labels.
1. Load the printer with media and ribbon.
2. Press the printer front panel MODE key until the CALIBRATE LED is lit.
3. Press the FEED key and allow the labels to feed.
4. When the labels have stopped press the MODE key once to save the value in memory.

Jul 10, 2009 | Zebra Stripe S500 Thermal Label Printer

1 Answer

Zebra 4M printer stopping due to error message


The printer is dirty sensor label or no label is calibrated. Turn off the printer and press FEED, CANCEL, PAUSE and turn on, release the keys to advancing the label, and let print be calibrated. Roberto Martinez Mexico [email protected]

Feb 26, 2009 | Zebra Z4M Printer

2 Answers

My Zebra z4m plus


in the setup menu there is an option to choose what the machine does on powerup and head close. Yours is probably set to calibrate. Just change that setting to "none". Same thing with the pausing. there is a setting to pause after printing each label. Just change that option.

Nov 02, 2008 | Zebra Z4M Printer

2 Answers

Zebra printer problem


chek on setings if the sennsor is reflective, transmissive or auto.
should be on Auto. try to read the Sensor profile, and check if read the gap.
Try the Manual calibration, and then run the sensor profile.
tur off and on again.

Apr 25, 2008 | Zebra Z4M Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...